SAE 1020 CARBON STEEL | DIN 1.0402 | AISI 1020 | S20C
SAE 1020 is a low-carbon, unalloyed steel with an average carbon content of approximately 0.20%. It is characterised by a good combination of strength, ductility, machinability and weldability. Its relatively low carbon content provides excellent formability and makes it suitable for conventional machining and fabrication operations. Although it has limited through-hardening capability, it can be carburised to develop a hard, wear-resistant surface while retaining a relatively tough core. It is widely used in general engineering and manufacturing applications.
ASM Digital Library+2
Typical uses are: Shafts, Pins, Bushings, Bolts, Spindles, Light-Duty Gears, Camshafts, Ratchets, Rollers, Machine Components and General Engineering Parts.
International Standard
| EU EN |
USA – |
Germany DIN,WNr |
Japan JIS |
France AFNOR |
England BS |
Italy UNI |
China GB |
Sweden SS |
Poland PN |
Czechia CSN |
Russia GOST |
Inter ISO |
| C22 | 1020 | C22 / 1.0402 | S20C | CC20 | 050A20 | C20 / C21 | 20 | 1450 | 20 | 12024 | 20 | C20 |
Available Types & Range
C 40 steel Supply Form & Size
| Form of Supply | Size(mm) | Length(mm) |
| Round bar | Φ20-Φ650 | Standard or As your request |
| Square bar | 25 x 25 – 450 x 450 | Standard or As your request |
| Plate/Sheet | Thickness :6 – 300 Width:80-1,250 |
Standard or As your request |
| Flat bar/Blcoks | Thickness :10 – 300 Width:120-25 – 500 |
Standard or As your request |
Chemical Composition & Technical Specification – SAE 1020
| Grade | C | Si | Mn | P | S |
| SAE 1020 / G10200 | 0.18–0.23 | — | 0.30–0.60 | ≤ 0.030 | ≤ 0.035 |
Surface Finish&Tolerance
| Surface Finish | Black-Forged | Black-Rolled | Turned | Grinding | Polished | Cold Drawn |
| Tolerance | (0,+5mm) | (0,+1mm) | (0,+3mm) | Best h9 | Best h9 | Best H10 |
C40 Steel Mechanical Property
| Diameter d mm | ≤ 16 | 16-40 | 40-100 |
| Thickness t mm | — | — | — |
| Yield Strength Mpa | 205–220* | 205–220* | 205–220* |
| Tensile Strength Mpa | 380–400* | 380–400* | 380–400* |
| Elongation, % | Approx. 25* | Approx. 25* | Approx. 25* |
| Reduction of area ,% | Approx. 50* | Approx. 50* | Approx. 50* |
SAE 1020 Steel Forging
Heat to 1100°C–1200°C and hold until the temperature is uniform throughout the section before commencing forging. Do not forge below 900°C. Finished forgings may be cooled in air.
Heat Treatment for SAE 1020 Steel
Normalizing
Heat to 890°C–940°C, hold until the temperature is uniform throughout the section, soak for 10–15 minutes and cool in still air.
Annealing
Heat to 870°C–910°C, hold until the temperature is uniform throughout the section and cool slowly in the furnace.
Hardening / Case Hardening
SAE 1020 has low hardenability and does not respond satisfactorily to conventional through-hardening. However, it is suitable for carburising and case hardening.
Carburizing
Pack, salt or gas carburise at 880°C–920°C, holding for sufficient time to develop the required case depth and carbon content. This should be followed by suitable core refining, case hardening and tempering treatments.
Core Refining
Slowly cool from the carburising temperature and reheat to 870°C–900°C. Hold until the temperature is uniform throughout the section and quench in oil, water or brine as required.
Case Hardening
Following core refining, reheat to 760°C–780°C and hold until the temperature is uniform throughout the section. Quench in water and temper immediately while still hand warm.
Tempering
After carburising, core refining and case hardening, reheat to 150°C–200°C. Hold until the temperature is uniform throughout the section, soak for approximately 1 hour per 25 mm of section thickness and cool in still air.
Tempering improves the toughness of the hardened case while causing only a slight reduction in case hardness.
SAE 1020 Steel Applications
SAE 1020 is widely used for general engineering components requiring good machinability, excellent weldability, ductility and moderate strength. It is also suitable for lightly stressed components requiring a hardened, wear-resistant surface with a relatively tough core.
Typical applications include Axles, Shafts, General Engineering Components, Machinery Parts, Camshafts, Light-Duty Gears, Gudgeon Pins, Ratchets, Spindles and Worm Gears.

